Hydraulic tools - hydraulic jack select 7 points


There are 7 points in the selection of hydraulic jack:
1 lift determination method
We use than needed (lift force) to increase the amount of load jack 20%~30%
It will be a plurality of hydraulic jacks mounted in use, because there will be uneven load, please use a sufficient margin top lift jack
2 stroke decision method
Please use the hydraulic jack - enough travel allowance
3 reset function
Single acting type:
Spring reset
The piston rod with a spring reset
The inverted or level when in use, the front end of the piston rod is equipped with accessories, will be difficult to reset or reset the phenomenon
Self weight (external force) reset
It is no spring. To get the piston rod in place, there must be an "external force""
It is no spring. The piston rod must be reset by a sealed "compressed gas"
Double action hydraulic reset
The reset by hydraulic, please in need of tensile force or speed reduction requires the use of very fast
Please use the inverted or - level, the front end of the piston rod is equipped with accessory use
The tension is about the size of the lift 1/2 please were confirmed by specifications
4 note when using
The hydraulic jack can be vertical, horizontal, oblique, inverted "arranged, but must be vertical load
5 working speed range
The no load: Max300mm/sec
When load: please use below Max300mm/sec
The heavy lifting speed is below 5mm/sec when appropriate
We need more than this rate, please consult us
6 use frequency
The use of high frequency, please use the strength type lifting hydraulic jack
7 use environment
We use at ambient temperature ~40 DEG C within the range of -5
The use of the standard hydraulic jack in the use of the sealing ring ambient temperature of -10 DEG C ~80 C
8 allowable lateral load of hydraulic jack
The hydraulic jack load bearing part full load, please be careful not to add inclined load and impact load
Allow the transverse load, please confirm through their respective specifications
SITUTE(SITOOT) TOOLS CO.,LTD.
Add:BinGang Industrial Zone,Yuhuan County,Taizhou City,Zhejiang Province,China
Tel:0086-576-87229709
Fax:0086-576-87296000
E-mail:sitoot@sitoot.com
sitoot@126.com

Comments

Post a Comment

Popular posts from this blog

Busbar Processor Mchine （DHY-150D）

Image
This machine is  in order to improve work efficiency To save hours of work,while the design and manufacture. Suitable for transmission and distr bution in a large workshop and site work, construction,and power distribution cabinets and switch cabinets,etc. The use of electrical appliances factory. The machine is equipped with:bending,cutting,punching functionality. Optional foot switch or wire switch,easy to operate. DHY-150D(三合一母线加工机) FUNCTIONS Iput voltage/control voltage Rating working oil pressure Outlet force of puncher Bus bar cutting capability Outlet force of bus bar cutter The...
Read more

SYK-8A Hydraulic Hole Digger Technical parameters

Image
SYK-8A Hydraulic Hole Digger Technical parameters FUNCTION:  1、Compact,light,fast.It could be used on carbon steel plate for digging roundd and square hies in 3mm or below.It could also be used with other specific dies of hole digger.The solid positioning drive lead to approach working point easily.  2、Wide hole digging range .It could be used on switchboard,power transmission panel,meter plate,steel plate to dig hole or punch hole.Operate convenientlylpunched holes smooth without burr.  3、It covers six kinds of dies,two bolts,one washer,hole digger unit and plastic carrying case.  4、It could be used for digging square hole if fitted with square dies.Any specific size of roundand square dies could be ordered. SYK-8A Hydraulic Hole Digger Technical parameters: Model Output (T) Ram stroke (mm) Punching Capacity(mm) Punch Dies(mm) Plate Thickenes Punch Range(mm) Stainless Steel Iron Steel Weight (kg) Volume (cm) SYK-8A 8 22 1.6 3 ø16-ø60 ø16,ø2...
Read more

Safety precautions for cutting machine-hydraulic tools

Image
Installation and commissioning 1, steel straightening machine should be installed on a flat solid ground. 2, the installation of the bearing frame, the center of the bearing groove to be aligned with the guide cylinder, the straightening cylinder, the lower cutter hole or the center line of the shear gear groove, and keep straight. 3, after the installation of the machine, must check whether the electrical circuit and parts are damaged, the connection of the machine is reliable, the transmission part is flexible, confirm the error before the trial operation. 4, the first empty machine operation, check the bearing (focus on examination of the straightening cylinder bearing), hammer, knife or cutting gear is working properly. Ensure that no abnormal condition, before feeding, test straightening and cutting. safety precautions in operation 1, according to the straight bar diameter, selecting proper straightening block, traction wheel groove and the rotation speed. Straightening block di...
Read more