Battery Crimping Tools Advantage-hydraulic tools

The pressure interface is made of special materials, and the pressing speed is very fast, and the primary compression can be completed only about 5 seconds.


1, free rotating pliers head, crimping head can be rotated 360 degrees, suitable for a wide range of applications;
2, the micro two stage hydraulic system, the pressure in the process of low pressure to make the piston (lower die seat) rapid advance, the mold and the terminal contacts the piston will be slow;
3, temperature sensor, tool long time continuous operation will prosperous heat, when the temperature exceeds 60 degrees C, the tool will appear fault prompt and automatic stop, protection tool is not burned, the temperature drops can continue to work;
4, error indicator, the use of operating error will be issued a red error warning lights, with a warning sound;
5, automatic reset function, automatic pressure relief hydraulic device, when the pressure relay reaches the maximum, the tool automatically stop pressure and release about 90% of the pressure;
6, manual reset function crimping process error, can be manually reset the piston (lower die seat) back to the original position;
7, switch button, you can click on the use, and then click to stop working;
8, with special material and antiskid rubber wrapped by fear;
9, equipped with imported material nylon shoulder strap, easy to carry;
10, high performance lithium ion battery, power source provides more robust, non discharge memory effect, ultra low power standby design can guarantee the long time of 6 months, at the same time allocation over discharge protection extended battery life, sliding type equipment for battery.
YUHUAN SITUTE(SITOOT) TOOLS CO.,LTD.
Add:BinGang Industrial Zone,Yuhuan County,Taizhou City,Zhejiang Province,China
Tel:0086-576-87229709
Fax:0086-576-87296000
Http://www.china-hydraulic-tools.com
Http://www.sitoot.com
E-mail:sitoot@sitoot.com
         sitoot@126.com
Google+:https://plus.google.com/100112816207310014877

Comments

Post a Comment

Popular posts from this blog

Busbar Processor Mchine （DHY-150D）

Image
This machine is  in order to improve work efficiency To save hours of work,while the design and manufacture. Suitable for transmission and distr bution in a large workshop and site work, construction,and power distribution cabinets and switch cabinets,etc. The use of electrical appliances factory. The machine is equipped with:bending,cutting,punching functionality. Optional foot switch or wire switch,easy to operate. DHY-150D(三合一母线加工机) FUNCTIONS Iput voltage/control voltage Rating working oil pressure Outlet force of puncher Bus bar cutting capability Outlet force of bus bar cutter The...
Read more

SYK-8A Hydraulic Hole Digger Technical parameters

Image
SYK-8A Hydraulic Hole Digger Technical parameters FUNCTION:  1、Compact,light,fast.It could be used on carbon steel plate for digging roundd and square hies in 3mm or below.It could also be used with other specific dies of hole digger.The solid positioning drive lead to approach working point easily.  2、Wide hole digging range .It could be used on switchboard,power transmission panel,meter plate,steel plate to dig hole or punch hole.Operate convenientlylpunched holes smooth without burr.  3、It covers six kinds of dies,two bolts,one washer,hole digger unit and plastic carrying case.  4、It could be used for digging square hole if fitted with square dies.Any specific size of roundand square dies could be ordered. SYK-8A Hydraulic Hole Digger Technical parameters: Model Output (T) Ram stroke (mm) Punching Capacity(mm) Punch Dies(mm) Plate Thickenes Punch Range(mm) Stainless Steel Iron Steel Weight (kg) Volume (cm) SYK-8A 8 22 1.6 3 ø16-ø60 ø16,ø2...
Read more

Safety precautions for cutting machine-hydraulic tools

Image
Installation and commissioning 1, steel straightening machine should be installed on a flat solid ground. 2, the installation of the bearing frame, the center of the bearing groove to be aligned with the guide cylinder, the straightening cylinder, the lower cutter hole or the center line of the shear gear groove, and keep straight. 3, after the installation of the machine, must check whether the electrical circuit and parts are damaged, the connection of the machine is reliable, the transmission part is flexible, confirm the error before the trial operation. 4, the first empty machine operation, check the bearing (focus on examination of the straightening cylinder bearing), hammer, knife or cutting gear is working properly. Ensure that no abnormal condition, before feeding, test straightening and cutting. safety precautions in operation 1, according to the straight bar diameter, selecting proper straightening block, traction wheel groove and the rotation speed. Straightening block di...
Read more