Safety requirements for steel bar cutting machine-hydraulic tools


(1) the working table should be kept at the bottom of the cutting tool, and the length of the worktable can be determined according to the length of the material.
(2) before starting, check and confirm that the cutter is free of cracks, the tool holder bolt is fastened and the protective cover is firm. Then turn the pulley by hand, check the gear meshing clearance, adjust the clearance of the cutter.
(3) after starting, it should be transported by air to check the transmission part and the bearing is running normally.
(4) when the machine does not reach the normal speed, it shall not be cut. When cutting materials, should use the cutter of the middle and lower parts, hold reinforced alignment edge quickly put, the operator should stand on the side of the fixed blade cloth reinforced, should be reinforced to prevent the end of pop wounding. Strictly with two hands on both sides of the blade to hold the reinforcement bent feed.
(5) no shear strength exceeds the diameter of reinforced and reinforced mechanical nameplate provisions and burning red. A cut a plurality of steel bars, the total cross-sectional area should be in the specified range.


(6) the shear of low alloy steel, should be replaced with a high hardness cutting knife, shear diameter should be consistent with the provisions of mechanical nameplate.
(7) when the material is cut short, the distance between the hand and the cutting knife should be maintained at more than 150mm, such as the holding end is less than 400mm, should adopt the casing or fixture will be pressed to reinforced or short head.
(8) during operation, it is strictly prohibited to remove the broken ends and debris near the cutter by hand. Steel bars around the swing and around the knife, shall not stay non operating personnel.
(9) the machine should be stopped immediately when it is found that the machine is not working properly, there is abnormal noise or the cutter is crooked.
(10) after operation, should cut off the power supply, with the steel brush to clear the debris between the cutter, clean and lubricate the machine.
(11) the hydraulic cutting machine before operation, should check and confirm the hydraulic oil level and motor rotation direction to meet the requirements. After the start, should run without load, loose open the oil valve, drain the cylinder body of the air in order to cut.
(12) manual hydraulic cutting machine before use, should the oil drain valve in a clockwise direction, after cutting, should immediately counterclockwise unscrew.  During the operation, the hand should be steady and cutting machine, and wear insulated gloves.
YUHUAN SITUTE(SITOOT) TOOLS CO.,LTD.
Add:BinGang Industrial Zone,Yuhuan County,Taizhou City,Zhejiang Province,China
Tel:0086-576-87229709
Fax:0086-576-87296000
Http://www.china-hydraulic-tools.com
Http://www.sitoot.com
E-mail:sitoot@sitoot.com
         sitoot@126.com
Google+:https://plus.google.com/100112816207310014877

Comments

Post a Comment

Popular posts from this blog

Busbar Processor Mchine （DHY-150D）

Image
This machine is  in order to improve work efficiency To save hours of work,while the design and manufacture. Suitable for transmission and distr bution in a large workshop and site work, construction,and power distribution cabinets and switch cabinets,etc. The use of electrical appliances factory. The machine is equipped with:bending,cutting,punching functionality. Optional foot switch or wire switch,easy to operate. DHY-150D(三合一母线加工机) FUNCTIONS Iput voltage/control voltage Rating working oil pressure Outlet force of puncher Bus bar cutting capability Outlet force of bus bar cutter The...
Read more

SYK-8A Hydraulic Hole Digger Technical parameters

Image
SYK-8A Hydraulic Hole Digger Technical parameters FUNCTION:  1、Compact,light,fast.It could be used on carbon steel plate for digging roundd and square hies in 3mm or below.It could also be used with other specific dies of hole digger.The solid positioning drive lead to approach working point easily.  2、Wide hole digging range .It could be used on switchboard,power transmission panel,meter plate,steel plate to dig hole or punch hole.Operate convenientlylpunched holes smooth without burr.  3、It covers six kinds of dies,two bolts,one washer,hole digger unit and plastic carrying case.  4、It could be used for digging square hole if fitted with square dies.Any specific size of roundand square dies could be ordered. SYK-8A Hydraulic Hole Digger Technical parameters: Model Output (T) Ram stroke (mm) Punching Capacity(mm) Punch Dies(mm) Plate Thickenes Punch Range(mm) Stainless Steel Iron Steel Weight (kg) Volume (cm) SYK-8A 8 22 1.6 3 ø16-ø60 ø16,ø2...
Read more

Safety precautions for cutting machine-hydraulic tools

Image
Installation and commissioning 1, steel straightening machine should be installed on a flat solid ground. 2, the installation of the bearing frame, the center of the bearing groove to be aligned with the guide cylinder, the straightening cylinder, the lower cutter hole or the center line of the shear gear groove, and keep straight. 3, after the installation of the machine, must check whether the electrical circuit and parts are damaged, the connection of the machine is reliable, the transmission part is flexible, confirm the error before the trial operation. 4, the first empty machine operation, check the bearing (focus on examination of the straightening cylinder bearing), hammer, knife or cutting gear is working properly. Ensure that no abnormal condition, before feeding, test straightening and cutting. safety precautions in operation 1, according to the straight bar diameter, selecting proper straightening block, traction wheel groove and the rotation speed. Straightening block di...
Read more