Hydraulic punching machine used in the process of note - hydraulic tools

Precautions in use
According to the machining diameter selection of mold, hydraulic punching machine with a total of 10.5, Phi Phi 13.5, Phi 17.5, Phi 20.5 die six specifications, suitable for M10, M12 and M14 respectively, M16, M18, M20 bolt, the upper and lower die between the workpiece and the clamping sleeve, unloading the workpiece, driving machine control valve flush a hole, loosen the unloading valve, die reset, loosen the unloading workpiece can be obtained.

1, hydraulic punching machine matching electric pump system pressure factory has been adjusted for the 63MPa range, the user can not be adjusted.
2, punching machine assembly, the lower mold, must be the upper and lower mold model is consistent, the mold must be fixed sleeve.
3, hydraulic punching machine die at the time to pay attention to the edge (a small aperture), must not be installed instead of machine damage.
4, hydraulic punching machine during operation, the operating pressure of the system under the condition of fast detachable connector.
5, attention should be paid to the hole when the production of materials, so as to avoid the mold hole plug and damage to equipment.
6, the row should be basically flat.
7, in the use of the process should pay attention to oil and gas.
8, in the case of load, shall not be removed quickly.
9, shall not be corrosive substances in the workplace or deposit.

YUHUAN SITUTE(SITOOT) TOOLS CO.,LTD.
Add:BinGang Industrial Zone,Yuhuan County,Taizhou City,Zhejiang Province,China
Tel:0086-576-87229709
Fax:0086-576-87296000
Http://www.china-hydraulic-tools.com
Http://www.sitoot.com
E-mail:sitoot@sitoot.com
         sitoot@126.com
Google+:https://plus.google.com/100112816207310014877

Comments

Post a Comment

Popular posts from this blog

Busbar Processor Mchine （DHY-150D）

Image
This machine is  in order to improve work efficiency To save hours of work,while the design and manufacture. Suitable for transmission and distr bution in a large workshop and site work, construction,and power distribution cabinets and switch cabinets,etc. The use of electrical appliances factory. The machine is equipped with:bending,cutting,punching functionality. Optional foot switch or wire switch,easy to operate. DHY-150D(三合一母线加工机) FUNCTIONS Iput voltage/control voltage Rating working oil pressure Outlet force of puncher Bus bar cutting capability Outlet force of bus bar cutter The...
Read more

SYK-8A Hydraulic Hole Digger Technical parameters

Image
SYK-8A Hydraulic Hole Digger Technical parameters FUNCTION:  1、Compact,light,fast.It could be used on carbon steel plate for digging roundd and square hies in 3mm or below.It could also be used with other specific dies of hole digger.The solid positioning drive lead to approach working point easily.  2、Wide hole digging range .It could be used on switchboard,power transmission panel,meter plate,steel plate to dig hole or punch hole.Operate convenientlylpunched holes smooth without burr.  3、It covers six kinds of dies,two bolts,one washer,hole digger unit and plastic carrying case.  4、It could be used for digging square hole if fitted with square dies.Any specific size of roundand square dies could be ordered. SYK-8A Hydraulic Hole Digger Technical parameters: Model Output (T) Ram stroke (mm) Punching Capacity(mm) Punch Dies(mm) Plate Thickenes Punch Range(mm) Stainless Steel Iron Steel Weight (kg) Volume (cm) SYK-8A 8 22 1.6 3 ø16-ø60 ø16,ø2...
Read more

Safety precautions for cutting machine-hydraulic tools

Image
Installation and commissioning 1, steel straightening machine should be installed on a flat solid ground. 2, the installation of the bearing frame, the center of the bearing groove to be aligned with the guide cylinder, the straightening cylinder, the lower cutter hole or the center line of the shear gear groove, and keep straight. 3, after the installation of the machine, must check whether the electrical circuit and parts are damaged, the connection of the machine is reliable, the transmission part is flexible, confirm the error before the trial operation. 4, the first empty machine operation, check the bearing (focus on examination of the straightening cylinder bearing), hammer, knife or cutting gear is working properly. Ensure that no abnormal condition, before feeding, test straightening and cutting. safety precautions in operation 1, according to the straight bar diameter, selecting proper straightening block, traction wheel groove and the rotation speed. Straightening block di...
Read more