Hydraulic Pipe Benders Precautions in use-hydraulic tools

1, when the machine starts to pay attention to the human body can not enter the rotation of the arm swept scale.
2, the machine tool operation, all personnel stop into the arm and pipe swept the space scale!
3, the hydraulic system of the machine tool is usually YA-N32 hydraulic oil (the original Trademark No. 20), under normal circumstances to replace once a year, the filter is necessary to clean together.

4, the adjustment of machine tool (die), should be adjusted by pressing the button to adjust their own. Never one person on the machine tool adjustment, another person in the control cabinet operation.
5, adjust the machine or empty should remove the core rod.
6, hydraulic system pressure is not greater than 14Mpa.
7, manual adjustment side push cylinder speed rotating arm should be rotated to more than 900 when adjusted for the adjustment speed of rotary arm bending mould marginal line speed change synchronization, thrust speed is greater than the push line speed rotary die in the lower marginal status manual.
8, the machine should be used after a period of time to see the chain tension, adhere to the upper and lower chain tightness.
9, active operation in core winding form, bent back, operators need to ensure a mandrel in the pipe inside, or to ensure that the core shaft in a bent arm back did not obstruct the appearance, otherwise, the core head or core rod that can be bent or broken.
YUHUAN SITUTE(SITOOT) TOOLS CO.,LTD.
Add:BinGang Industrial Zone,Yuhuan County,Taizhou City,Zhejiang Province,China
Tel:0086-576-87229709
Fax:0086-576-87296000
Http://www.china-hydraulic-tools.com
Http://www.sitoot.com
E-mail:sitoot@sitoot.com
         sitoot@126.com
Google+:https://plus.google.com/100112816207310014877

Comments

Post a Comment

Popular posts from this blog

Busbar Processor Mchine （DHY-150D）

Image
This machine is  in order to improve work efficiency To save hours of work,while the design and manufacture. Suitable for transmission and distr bution in a large workshop and site work, construction,and power distribution cabinets and switch cabinets,etc. The use of electrical appliances factory. The machine is equipped with:bending,cutting,punching functionality. Optional foot switch or wire switch,easy to operate. DHY-150D(三合一母线加工机) FUNCTIONS Iput voltage/control voltage Rating working oil pressure Outlet force of puncher Bus bar cutting capability Outlet force of bus bar cutter The...
Read more

SYK-8A Hydraulic Hole Digger Technical parameters

Image
SYK-8A Hydraulic Hole Digger Technical parameters FUNCTION:  1、Compact,light,fast.It could be used on carbon steel plate for digging roundd and square hies in 3mm or below.It could also be used with other specific dies of hole digger.The solid positioning drive lead to approach working point easily.  2、Wide hole digging range .It could be used on switchboard,power transmission panel,meter plate,steel plate to dig hole or punch hole.Operate convenientlylpunched holes smooth without burr.  3、It covers six kinds of dies,two bolts,one washer,hole digger unit and plastic carrying case.  4、It could be used for digging square hole if fitted with square dies.Any specific size of roundand square dies could be ordered. SYK-8A Hydraulic Hole Digger Technical parameters: Model Output (T) Ram stroke (mm) Punching Capacity(mm) Punch Dies(mm) Plate Thickenes Punch Range(mm) Stainless Steel Iron Steel Weight (kg) Volume (cm) SYK-8A 8 22 1.6 3 ø16-ø60 ø16,ø2...
Read more

Safety precautions for cutting machine-hydraulic tools

Image
Installation and commissioning 1, steel straightening machine should be installed on a flat solid ground. 2, the installation of the bearing frame, the center of the bearing groove to be aligned with the guide cylinder, the straightening cylinder, the lower cutter hole or the center line of the shear gear groove, and keep straight. 3, after the installation of the machine, must check whether the electrical circuit and parts are damaged, the connection of the machine is reliable, the transmission part is flexible, confirm the error before the trial operation. 4, the first empty machine operation, check the bearing (focus on examination of the straightening cylinder bearing), hammer, knife or cutting gear is working properly. Ensure that no abnormal condition, before feeding, test straightening and cutting. safety precautions in operation 1, according to the straight bar diameter, selecting proper straightening block, traction wheel groove and the rotation speed. Straightening block di...
Read more